Linux ETC

ethtool

2008.05.19 20:36

호스트웨이 조회 수:29609

ethtool 명령을 이용하여 랜카드 속도 및 전송 모드 지정하는 방법입니다.

1. 현재 eth0 설정 확인

아래와 같이 현재 eth0 카드의 설정을 확인합니다.

[root@sakang /]# ethtool eth0
Settings for eth0:
       Supported ports: [ TP MII ]
       Supported link modes:   10baseT/Half 10baseT/Full
                               100baseT/Half 100baseT/Full
       Supports auto-negotiation: Yes
       Advertised link modes:  10baseT/Half 10baseT/Full
                               100baseT/Half 100baseT/Full
       Advertised auto-negotiation: Yes
       Speed: 100Mb/s
       Duplex: Full

       Port: MII
       PHYAD: 1
       Transceiver: internal
       Auto-negotiation: on
       Supports Wake-on: pumbg
       Wake-on: d
       Current message level: 0x00000001 (1)
       Link detected: yes


현재 스피드가 100M 이고 전송모드는 Full Duplex  임을 확인할 수 있습니다.



2. 10M 로 변경하기

ethtool -s eth0 speed 10 duplex full autoneg on

위 명령으로 스피드를 10M 변경하고 확인해 봅시다.

[root@sakang /]# ethtool eth0
Settings for eth0:
       Supported ports: [ TP MII ]
       Supported link modes:   10baseT/Half 10baseT/Full
                               100baseT/Half 100baseT/Full
       Supports auto-negotiation: Yes
       Advertised link modes:  10baseT/Full
       Advertised auto-negotiation: Yes
       Speed: 10Mb/s
       Duplex: Full
       Port: MII
       PHYAD: 1
       Transceiver: internal
       Auto-negotiation: on
       Supports Wake-on: pumbg
       Wake-on: d
       Current message level: 0x00000001 (1)
       Link detected: yes

스피드가 10M 로 변경 되었습니다.

3. duplex 변경

아래 명령으로 전송모드를 변경할 수 있습니다.

ethtool -s eth0 speed 10 duplex half autoneg on

eth0 을 확인해 보면

Settings for eth0:
       Supported ports: [ TP MII ]
       Supported link modes:   10baseT/Half 10baseT/Full
                               100baseT/Half 100baseT/Full
       Supports auto-negotiation: Yes
       Advertised link modes:  10baseT/Half
       Advertised auto-negotiation: Yes
       Speed: 10Mb/s
       Duplex: Half

       Port: MII
       PHYAD: 1
       Transceiver: internal
       Auto-negotiation: on
       Supports Wake-on: pumbg
       Wake-on: d
       Current message level: 0x00000001 (1)
       Link detected: yes

전송 모드가 half Duplex 로 변경되었습니다.

이 상태에서 ethtool -s eth0 autoneg off 명령으로 자동협상기능을 끄고

ethtool -s eth0 autoneg on 명령으로 다시 켭니다.

그리고 나서 eth0 카드를 확인해 보면 100M Full Duplex 로 바뀌어져 있습니다.

이유는 eth0 카드와 연결된 스위치의 설정이 100M Full Duplex 이기 때문입니다.



사용 방법이 비슷한 mii-tool 이란 도구도 있으니 한번 사용해 보시기 바랍니다.